<p>Austria’s first 3D-printed building is being constructed in Hausleiten, Lower Austria. Construction technology group STRABAG, together with PERI, the formwork and scaffolding manufacturer and a pioneer in 3D concrete printing, is realising a roughly 125 square meters office building next to its asphalt mixing plant in Hausleiten. The special dry mortar for the construction 3D printing project, with long workability and good pumpability, is being supplied by Lafarge.</p><p>Construction 3D printing offers several advantages where its use makes technical and financial sense. The COBOD BOD2 gantry printer used in Hausleiten can print concrete at up to one metre per second, which significantly shortens the construction time. The structural works for the building in Hausleiten can be completed in around 45 hours of pure printing time. Construction 3D printing also offers significantly more design freedom compared to classic concrete construction, with the possibility of easily creating architecturally complex rounded designs.</p><p>PERI is using the COBOD BOD2 gantry printer for the construction printing project in Hausleiten. This printing technology comes from Danish manufacturer COBOD, in which PERI acquired a significant stake in 2018.</p><p>The print head moves about three axes on a securely installed metal frame. This allows the printer to be moved to any position in the structure being built, requiring only a single calibration. The 3D printer applies the print material (dry mortar) in layers to create the walls. Laying down two parallel printing paths creates a hollow wall that is then backfilled with cast-in-place concrete as a load-bearing system. To create the outer wall, a second cavity is formed by printing another mortar path further outside the previous wall and filling this with thermal insulation material. The printed walls can be regarded as a kind of lost formwork system.</p><p>During the printing process, the printer already takes into account the water, electricity and other utility lines and connections that will be installed at a later point. The BOD2 is certified in such a way that work can also be carried out in the print room during the printing process. This allows manual work, such as the laying of pipes and connections, to be easily integrated into the printing process.</p><p>The printing material is stored in silos. The ready-to-use dry mortar is then pumped directly into the print head during the printing process after the addition of water. The Tector Print brand material used for printing the office building in Hausleiten was developed by Holcim and is adapted to the special requirements of 3D concrete printing.</p>
<p>Austria’s first 3D-printed building is being constructed in Hausleiten, Lower Austria. Construction technology group STRABAG, together with PERI, the formwork and scaffolding manufacturer and a pioneer in 3D concrete printing, is realising a roughly 125 square meters office building next to its asphalt mixing plant in Hausleiten. The special dry mortar for the construction 3D printing project, with long workability and good pumpability, is being supplied by Lafarge.</p><p>Construction 3D printing offers several advantages where its use makes technical and financial sense. The COBOD BOD2 gantry printer used in Hausleiten can print concrete at up to one metre per second, which significantly shortens the construction time. The structural works for the building in Hausleiten can be completed in around 45 hours of pure printing time. Construction 3D printing also offers significantly more design freedom compared to classic concrete construction, with the possibility of easily creating architecturally complex rounded designs.</p><p>PERI is using the COBOD BOD2 gantry printer for the construction printing project in Hausleiten. This printing technology comes from Danish manufacturer COBOD, in which PERI acquired a significant stake in 2018.</p><p>The print head moves about three axes on a securely installed metal frame. This allows the printer to be moved to any position in the structure being built, requiring only a single calibration. The 3D printer applies the print material (dry mortar) in layers to create the walls. Laying down two parallel printing paths creates a hollow wall that is then backfilled with cast-in-place concrete as a load-bearing system. To create the outer wall, a second cavity is formed by printing another mortar path further outside the previous wall and filling this with thermal insulation material. The printed walls can be regarded as a kind of lost formwork system.</p><p>During the printing process, the printer already takes into account the water, electricity and other utility lines and connections that will be installed at a later point. The BOD2 is certified in such a way that work can also be carried out in the print room during the printing process. This allows manual work, such as the laying of pipes and connections, to be easily integrated into the printing process.</p><p>The printing material is stored in silos. The ready-to-use dry mortar is then pumped directly into the print head during the printing process after the addition of water. The Tector Print brand material used for printing the office building in Hausleiten was developed by Holcim and is adapted to the special requirements of 3D concrete printing.</p>